San Severo Manufacturer of scissor liftOverview of investigation on the condition

Before installation， the installer should confirm the infrastructure such as the foundation and the shaft， pay attention to alignment， leveling， and alignment， and confirm that the foundation meets the requirements before construction.

1lifting platformTo check whether the gear oil in the oil tank reaches the standard volume，Products check whether the oil tank leaks oil，TurkwanLogistics hydraulic lifting platformWhat are the types of if the gear oil is insufficient， please add # gear oil， which can be found in hardware stores.

wSan Severo Hydraulic Freight Elevator Hydraulic Hoist Lifting Platform Freight Elevator is a kind of lifting mechanical equipment， the lifting system of hydraulic lift freight elevator is driven by hydraulic pump station， and the lifting power of the platform is a two-machine or three-phase power supply. There are manual and electric， and a hand pump is also available for power failure. This series of platforms has flexible movement， stable lifting， and convenient operation. Features， mainly used in factories，Products institutions， shops and construction and decoration industries.

OAngolaThe lifting platform can only be raised and cannot be lowered: check whether the indicator light of the vacuum solenoid valve is on， press the down button on the power box， if the light on the vacuum solenoid valve does not flash， check whether the two lines of the vacuum solenoid valve are short-circuited or not loose.

KuThe boxes and distribution boxes are always kept clean， and the dust on the electrical equipment is cleaned in time.The contact opening and closing of the travel switch must be reliable， and the contact arc crater should be polished in time.

According to safety， in addition to general safety devices a safe and stable hydraulic freight elevator should also have a relief valve to prevent excessive pressure during upward movement. When the hydraulic system pipeline ruptures and causes rapid descent， there should be a pipeline rupture valve that can automatically cut off the oil circuit; must With an emergency handbrake， it can be stopped immediately in an emergency to avoid damage. Therefore，Products buyers need to choose hydraulic freight elevators with pipe rupture valves and emergency hand brakes for safer.

The vibration range is proportional to the lifting height. The higher the height， the greater the shaking range，TurkwanLogistics hydraulic lifting platformWhat are the types of the wind ropes at the four corners of the hydraulic cargo elevator should be tightened to strengthen leg protection， increase stability and reduce shaking.

nThe aging of composite cushions and sealing rings between silk boards and joints will also increase the chance of oil leakage. If the lifting platform leaks oil and you don’t know how to deal with it， you can first use polymer composite materials to add curing agent to deal with the oil leakage. Then analyze the cause of oil leakage. The above is the reason why the hydraulic freight elevator may leak oil， we canIt can be resolved by analyzing the reasons.

KOil leakage from the oil cylinder: If it is the sealing ring problem， replace the sealing ring. If the oil cylinder has sundries and debris wear， it is recommended to replace the oil cylinder with a new one.

XconsumptionThe development of elevators is at its peak， because many manufacturers choose more multi-storey buildings in order to make full use of the space， so a kind of equipment is also needed to facilitate the improvement of goods.

hEBefore lifting and lowering the lifting platform，Elevator Price_ Hydraulic ladder_ Household elevator_ Household elevator - elevator manufacturer place the four corner legs. The four legs should be firmly supported on the solid ground， and the worktable should be adjusted to a horizontal state (visual inspection is sufficient). Turn on the power， the indicator light should be on. Then start the motor， work the oil pump go up and down once or twice under no-load， check the normal operation of each part and then start working. When the temperature is lower than °C， the oil pump should be operated for - minutes， and it can only be carried out after confirming that the oil pump is working normally. . After entering the platform， the operator should close the guardrail door， insert the latch， and fasten the safety rope. The center of the load (the position where people stand) should be as close as possible to the center of the work surface. Lifting and falling: press the lift button to start the motor ， the motor rotates， the hydraulic system works， the oil cylinder stretches out， and the platform rises; when it reaches the height required for the work， the platform stops lifting， and you can work， if you dont press the stop button， the platform rises When reaching the calibrated height， the travel switch works， and the platform stops at the calibrated height. After the work is completed， press the down button， the solenoid valve will act， and the oil return of the oil cylinder will be connected at this time， and the platform will drop by its own weight.

B. Remove and disassemble the down valve， blow out the valve core with compressed air and install it again.

The hydraulic freight elevator manufacturer reminds that the electric hoist freight elevator completes the lifting of the freight elevator through the pulling of several steel wire ropes. This kind of freight elevator often causes the platform of the lifting freight elevator to be skewed due to the tightness of the steel wire ropes， and the stability and safety are poor. Limited， it can only be used for the transportation of small tonnage goods， so the wire rope freight elevator is increasingly replaced by the hydraulic guide rail type elevator.

Manufacturing costwlifting platformTo check whether the gear oil in the oil tank reaches the standard volume， check whether the oil tank leaks oil， if the gear oil is insufficient， please add # gear oil， which can be found in hardware stores.

ZSo， how to choose a high-quality lift? The first is to screen the lifting platform manufacturer; there is nothing wrong with choosing yourself and it is more correct to choose your own manufacturer! Good equipment and after-sales service are to ensure their legitimate rights and interests and ensure that the equipment they choose will bring huge benefits; therefore， choosing a formal manufacturer with complete production qualifications and companies that have obtained product quality certification and rewards is important to ensure their own rights and interests Guarantee， it is very important to choose a high-quality manufacturer. The hydraulic lift is composed of a platform and its equipment， motors， cables and other auxiliary equipment， and is composed of lifting machinery or equipment on the vertical upper and lower passages or semi-enclosed platforms; its working principle is: hydraulic oil forms a certain pressure through the vane pump through The oil filter， anti-electromagnetic reversing valve， check valve， and balance valve enter the lower end of the hydraulic cylinder to move the piston of the hydraulic cylinder upward and lift heavy objects. The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the anti-electromagnetic reversing valve the rated pressure is adjusted through the overflow valve， and the reading value of the pressure gauge is observed through the pressure gauge. I have been engaged in the sales of various elevator manufacturers and other materials all year round. I operate with integrity. Welcome to call!

Solution: Check whether the performance of the outrigger is good， even if it is polished with butter to increase its lubricity.

tSan Severo Next， the hydraulic freight elevator manufacturer will tell you about the maintenance of the elevator mechanical equipment: the brakes of each organization should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. On the surface， there should be no dirt， and if there is dirt， and the concentrated load of the MAX load capacity is placed at any position mm away from the periphery of the workbench. After lifting times， each stressed member must not be deformed or cracked.

If the circuit of the device is not disconnected or dropped， the fuse needs to be checked for repair and replacement.