hengelo Hydraulic lifting platform Electric lifting platformWeak demand in the short term or still under pressure

. Road noise If the tires are crushed on objects that are prone to noise， noise will also be generated. The shaking range of the scissor lift platform is proportional to its lifting height. The higher the height， the greater the shaking. When using it at a working height of meters， please use safety protection measures if possible.

7Frequently check whether each organization can work normally and whether there is noise. If any problem is found， it should be cleaned up in time.

chengelo The chain-rail elevator is equipped with the safety device of the traditional traction elevator， but it also has: overflow valve: when the system is running，Domestic elevator it can prevent the system pressure from being too high; emergency manual valve: when the power fails，NangongHydraulic ladderHow should rust be remedied it can make the car drop down to Open the door at the nearest floor; manual pump: when the system fails， the manual pump can be operated to pump out high-pressure oil to make the car rise to the nearest floor; pipeline rupture valve: when the hydraulic system pipeline ruptures， when the system fails In case of failure， the manual pump can be operated to pump out high-pressure oil to make the car rise to the nearest floor; pipeline rupture valve: when the hydraulic system pipeline ruptures， it can automatically cut off the oil circuit to stop the descent.

There is a self-stop phenomenon when running up and down， which is easily caused by the poor contact of the safety protection switch contacts.

TKhemis El khechnaThe guide rail lift is a scissor-like hydraulic lifting platform， which is suitable for the transportation of goods between the floors of industrial plants， restaurants and restaurants on the third floor. The minimum height is -mm， the operation is simple and reliable，Domestic elevator and it has multiple protections of hydraulic pressure and electricity， and the transportation of goods is economical and convenient.

GqPay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations， it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with the regular inspection of the connection of each part， and all connecting shafts must have cotter pins and must be fully opened.

Frequently check whether each organization can work normally and whether there is noise. If any problem is found it should be cleaned up in time.

The second is that the goods loaded on the guide rail elevator should be uniform: when the guide rail elevator is working， you must pay attention to the placement of the goods. The cargo weight of some guide rail elevators is within the rated load range， but the cargo tends to be placed on one side or a corner so the guide rail elevator is the same as the overload， especially the aluminum alloy elevator， when placing the cargo， it must be placed as evenly as possible or placed in the center.

wAll work at heights must first build scaffolding or take measures to prevent the team from falling， before boarding the bridge.

HThe hydraulic freight elevator manufacturer reminds that the electric hoist freight elevator completes the lifting of the freight elevator through the pulling of several steel wire ropes. This kind of freight elevator often causes the platform of the lifting freight elevator to be skewed due to the tightness of the steel wire ropes，Domestic elevator and the stability and safety are poor. Limited， it can only be used for the transportation of small tonnage goods，NangongHydraulic ladderHow should rust be remedied so the wire rope freight elevator is increasingly replaced by the hydraulic guide rail type elevator.

IRangeThe hydraulic lifting platform is an indispensable and important operating equipment in society， and this is the case， hydraulic freight elevator wholesale manufacturers will often forget to maintain the hydraulic lifting platform， just like this， it will cause damage to the equipment， reduce work efficiency， and pose a threat to life safety Threat， therefore，Elevator Price_ Hydraulic ladder_ Household elevator_ Household elevator - elevator manufacturer in order to prolong the service life of the hydraulic lifting platform， it is necessary to use and maintain the equipment reasonably. The following points are the maintenance of the hydraulic lifting platform.

aTThe load and load of the hydraulic elevator act directly on the foundation pit through the oil cylinder. The strength of the shaft is low and the shaft of brick structure or brick-concrete structure is sufficient.

The contact surface of each part of the brush should be kept clean， and the pressure of the brush should be adjusted so that the contact area is not less than %.

Before work， the staff close the movable doors at both ends of the guardrail and start the bell. It is strictly forbidden to work when the movable door of the guardrail is open. In the operation of the hydraulic elevator， in case of special circumstances， the emergency stop switch can be used to stop the hydraulic elevator， but in normal operation， it is forbidden to use the emergency stop switch to stop.

Online consultationn.The cause of the noise failure of the elevator pump station: the motor wiring is wrong and when the system pressure rises， the noise increases. The motor coil winding is faulty. The outriggers should be opened before the lift works. In this case， noise will be generated.

GAdvantages of geotechnical engineering: no machine room is required above the well， and the top floor height can reach more than meters.

The noise of the oil cylinder of the elevator is too low， and the air is sucked into the oil from the oil filter or the connection of the joint. The coupling is loose. The internal failure of the oil cylinder. Inhale the air or the oil pipe on the oil surface， mix the air into the oil and remove it: the concentricity should be adjusted to within .MM， correct the coupling， repair or replace the oil pump， increase the oil volume， replace the rotating shaft seal ring at the position of the oil filter and the joint above mm Clean the oil filter screen， filter the oil and lock the oil return pipe， extend the oil return pipe to the oil surface， and the oil is mixed with air or the air in the hydraulic cylinder is not completely exhausted， and cavitation occurs under high pressure. cause loud noise. At this time， the air must be exhausted in time.

khengelo The capacity should be considered. Generally， the maximum flow rate of the pump is to times for mobile equipment， and to times for fixed equipment.

pABefore installation， the installer should confirm the infrastructure such as the foundation and the shaft， pay attention to alignment， leveling， and alignment， and confirm that the foundation meets the requirements before construction.

The material enters the production line at one end of the plant， and the plant where the production process ends at the other end is equipped with a separate platform; this can minimize the distance that materials flow in the plant.